Emissions from sawdust in packed moving bed dryers and subsequent pellet production

This study quantifies emissions of hydrocarbon terpenes from the drying of sawdust in packed moving bed dryers, through the production chain to the finished pellets, and determines the parameters suitable for emission control. The terpene content in softwood sawdust and pellets was analyzed using gas chromatography. The distribution of VOC emissions over the bed was measured with a flame ionization detector. After drying, 30–40% of the initial terpenes remain in the wood, 20–30% remain after grinding, and 10–15% remain after pelleting. Dryer emissions correlate with residence time and final sawdust moisture content. Pellet press emissions correlate with pellet moisture content.     

Processing of wood plastic composites: The influence of feeding method and polymer melt flow rate on particle degradation

Spruce wood particle (WP)/polypropylene (PP) compounds were prepared in an internal mixer using different rotor speeds. To analyze the effect of feeding method on particle degradation, WP and PP were either fed as dry‐blend or WP was fed into the PP melt. To prevent melt freezing, pre‐heated WP were used as comparison to cold WP. In addition, WPs were compounded with different grades of PP or high‐density polyethylene (HDPE) to analyze the effect of polymer matrix melt flow rate (MFR) on particle degradation. Mixing behavior of compounds containing 30% and 70% (w/w) WP depended on feeding method, represented by a changing relation of final torque values. Feeding as dry‐blend and using pre‐heated particles led to stronger WP degradation. Degradation decreased with increasing polymer MFR. For PP compounds, particle degradation was stronger when containing 70% WP, for HDPE the difference due to WP content was only marginal. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43231.     

Characteristics of wet‐spun and thermally treated poly acrylonitrile fibers

The performance of carbon fibers depends on the quality of the precursor and the conditions of the thermal treatment. In detail, for a PAN precursor fiber the viscosity of a spinning dope and the draw ratio during the spinning process needs to be considered. Through wet spinning, different types of PAN precursor fibers with defined spinning parameters, including solid content, solvent content in a bath, and especially draw ratio resulting in defined cross section diameters, were fabricated and analyzed with tensile tests, density investigations, SEM, TGA‐MS, FTIR, and XRD. The results show that the mechanical properties of the fibers correlate to crystallinity. The cross section diameter is strongly related to the morphology of the fibers after thermal treatment. By extending the postdrawing of PAN fibers high tenacities were obtained at the cost of the cross section shape. In addition, TGA measurements reveal trapped residues of the wet spinning process as well as show several chemical reactions takes place at the same time at different temperatures. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43698.     

Functionalized galactoglucomannan‐based hydrogels for the removal of metal cations from aqueous solutions

New types of hydrogels derived from O‐acetyl galactoglucomannan (AcGGM) hemicellulose have been synthesized and characterized. The objective of this work was to analyze the sorption capacity (S) of three types of hydrogels containing AcGGM derivatives incorporated into the carboxylic groups of the polymer chain in the AA hydrogel, sulfonic groups in the APA hydrogel, and amide groups in the acrylamide (Aam) hydrogel. These hydrogels are capable of interacting and removing ions such as cadmium [Cd(II)], copper [Cu(II)], lead [Pb(II)], nickel [Ni(II)], and zinc [Zn(II)]. The results show that AA and Aam hydrogels had a lower sorption capacity of ions compared to the APA hydrogel, which had a high sorption capacity. The maximal sorption capacity was determined by the successive enrichment method, obtaining Pb(II) amount of 48.3 mg/g of AA hydrogel, 65.8 mg/g of APA hydrogel, and 40.8 mg/g of Aam hydrogel. Hence, Pb(II) ions are greatly retained by the three hydrogels. These results are promising for the development of new materials with potential applications in metal ion removal. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44093.     

Polyurethanes based on 2,2‐Dinitropropane‐1,3‐diol and 2,2‐bis(azidomethyl)propane‐1,3‐diol as potential energetic binders

On the base of 2,2‐bis(azidomethyl)propane‐1,3‐diol (BAMP) and 2,2‐dinitropropane‐1,3‐diol (DNPD) four different polyurethanes were synthesized in a polyaddition reaction using hexamethylene diisocyanate (HMDI) and diisocyanato ethane (DIE). The obtained prepolymers were mainly characterized using vibrational spectroscopy (IR) and elemental analysis. For determination of low and high temperature behavior, differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) were used. Investigations concerning friction and impact sensitivities were carried out using a BAM drop hammer and friction tester. The energetic properties of the polymers were determined using bomb calorimetric measurements and calculated with the EXPLO5 V6.02 computer code. The obtained values were compared with the glycidyl azide polymer (GAP). The compounds turned out to be insensitive toward friction (>360 N) and less sensitive toward impact (40 J). The good physical stabilities, along with their sufficient thermal stability (170–210 °C) and moderate energetic properties renders these polymers into potential compounds for applications as binders in energetic formul;ations. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43991.     

Cellulose Aerogel Fibers Tested on a REXUS 18 Rocket – The ACTOR Project

Aerogels are high‐performance materials used for space and aviation purposes. Cellulose aerogel fibers have been investigated under real space conditions for their insulation properties. The experiments were carried out in a one‐stage high‐altitude research rocket of the improved ORION type. A cuboid module with measurement cells, camera modules, and electronic devices has been developed for monitoring the insulation behavior of cellulose aerogel non‐woven samples. The thermal behavior of these samples has been analyzed and compared to cellulose cloth (cotton) and aluminum for reference.     

Ultra-trace Analysis of Enantiomeric Impurities in Proteinogenic N-Fmoc-Amino-acid Samples on Cinchona Alkaloid-based Chiral Stationary Phases

The enantiomeric purity of N_α-Fmoc-protected amino acids is crucial from the viewpoint of peptide synthesis; therefore, a sensitive high-performance liquid chromatographic protocol was developed for the identification and quantification of enantiomeric impurities of commercially available N_α-Fmoc-protected amino acids on Cinchona alkaloid quinine- and quinidine-based weak anion exchanger-type chiral stationary phases. In the course of the evaluation of the chiral chromatographic method, the effect of the mobile phase composition, nature, and concentration of different additives were optimized. The specific phenomenon that quinine- and quinidine-based chiral stationary phases behave as pseudo-enantiomers permits that the sequence of elution of the enantiomers might be reversed by simple column switching. This is quite advantageous as regards the separation of the minor component in the presence of the major one. The method developed permits detection of less than 0.01 % enantiomeric impurity in the presence of the major enantiomer.     

Effects of antimicrobial agents on the thermal and mechanical properties of acrylate hydrogel matrices

Polymer materials with antimicrobial activity are prepared by UV polymerization of acrylate and methacrylate mixture at room temperature. The antimicrobials are silver acetate and copper (II) acetate, used without pretreatment. Their chemical stability in the acrylate matrix and their effect on the thermal and mechanical properties of the polymer matrix are investigated as a function of their concentration up to 15 wt %. Physico‐chemical, thermal, rheological, and morphological analyses as well as the surveillance of metal salts release in aqueous medium are conducted. A significant decrease in the thermal stability of the salts introduced into the acrylate matrix is observed after UV treatment. The metal salts also have significant effects on the properties of the matrix. A plasticization and densification of the material associated with an aggregation of salts up to the percolation at the highest concentration are highlighted. At equal concentrations, the effects are more pronounced in the presence of copper salts. The latter was released more slowly than silver salts from acrylate material. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43501.     

Synthesis and Biopharmaceutical Evaluation of Imatinib Analogues Featuring Unusual Structural Motifs

A convenient synthesis of imatinib, a potent inhibitor of ABL1 kinase and widely prescribed drug for the treatment of a variety of leukemias, was devised and applied to the construction of a series of novel imatinib analogues featuring a number of non‐aromatic structural motifs in place of the parent molecule's phenyl moiety. These analogues were subsequently evaluated for their biopharmaceutical properties (e.g., ABL1 kinase inhibitory activity, cytotoxicity). The bicyclo[1.1.1]pentane‐ and cubane‐containing analogues were found to possess higher themodynamic solubility, whereas cubane‐ and cyclohexyl‐containing analogues exhibited the highest inhibitory activity against ABL1 kinase and the most potent cytotoxicity values against cancer cell lines K562 and SUP‐B15. Molecular modeling was employed to rationalize the weak activity of the compounds against ABL1 kinase, and it is likely that the observed cytotoxicity of these agents arises through off‐target effects.